Lektrico Charging Station
The Lektrico Charging Station integration integrates your Lektrico Charging Station
The Lektrico Charging Station device will be added as a sensor in Home Assistant.
Configuration
To add the Lektrico Charging Station device to your Home Assistant instance, use this My button:
Lektrico Charging Station can be auto-discovered by Home Assistant. If an instance was found, it will be shown as Discovered. You can then set it up right away.
If it wasn’t discovered automatically, don’t worry! You can set up a manual integration entry:
-
Browse to your Home Assistant instance.
-
In the bottom right corner, select the
Add Integration button. -
From the list, select Lektrico Charging Station.
-
Follow the instructions on screen to complete the setup.
Binary sensors
Binary sensors available in the library:
Chargers
| Condition | Description |
|---|---|
| state_e_activated | Electric vehicle error |
| overtemp | Overtemperature |
| critical_temp | Critical temperature |
| overcurrent | Overcurrent |
| meter_fault | Meter fault |
| undervoltage | Undervoltage |
| overvoltage | Overvoltage |
| rcd_error | RCD error |
| cp_diode_failure | Electric vehicle communication error |
| contactor_failure | Contactor failure |
Sensors
Sensors available in the library:
Single-phase charger
| Condition | Unit | Description |
|---|---|---|
| state | State of the charger. | |
| charging_time | s | Indicates the current session charging time. |
| power | kW | Current instant power. |
| energy | kWh | Total charged energy for the current charging session. |
| temperature | °C | Board temperature. |
| lifetime_energy | kWh | Total charged energy since installation. |
| installation_current | A | Current value [A] to be limited by software. |
| limit_reason | Current limit reason. | |
| voltage | V | Measured voltage. |
| current | A | Measured current. |
Three-phase charger
| Condition | Unit | Description |
|---|---|---|
| state | State of the charger. | |
| charging_time | s | Indicates the current session charging time. |
| power | kW | Current instant power. |
| energy | kWh | Total charged energy for the current charging session. |
| temperature | °C | Board temperature. |
| lifetime_energy | kWh | Total charged energy since installation. |
| installation_current | A | Current value [A] to be limited by software. |
| limit_reason | Current limit reason. | |
| voltage_l1 | V | Measured voltage on L1. |
| voltage_l2 | V | Measured voltage on L2. |
| voltage_l3 | V | Measured voltage on L3. |
| current_l1 | A | Measured current on L1. |
| current_l2 | A | Measured current on L2. |
| current_l3 | A | Measured current on L3. |
Single-phase energy meter
| Condition | Unit | Description |
|---|---|---|
| breaker_current | A | Main breaker current. |
| power | kW | Measured active power. |
| pf | Power factor. |
Three-phase energy meter
| Condition | Unit | Description |
|---|---|---|
| breaker_current | A | Main breaker current. |
| power_l1 | kW | Measured active power on L1. |
| power_l2 | kW | Measured active power on L2. |
| power_l3 | kW | Measured active power on L3. |
| pf_l1 | Power factor on L1. | |
| pf_l2 | Power factor on L2. | |
| pf_l3 | Power factor on L3. |
Buttons
Buttons available in the library:
Chargers
| Button | Description |
|---|---|
| charge_start | Command charger to start charging. |
| charge_stop | Command charger to stop charging. |
| reboot | Reboot charger. |
Energy meters
| Button | Description |
|---|---|
| reboot | Reboot energy meter. |
Numbers
Numbers available in the library:
Chargers
| Number | Unit | Range | Description |
|---|---|---|---|
| led_max_brightness | % | 0 - 100 | Set the LED brightness of the charger. |
| dynamic_limit | A | 0 - 32 | Set the maximum allowed charging current. |
Selects
Selects available in the library:
Energy meters
| Select | Description |
|---|---|
| lb_mode | Select the load balancing mode of the energy meter. The options are Disabled, Power, Hybrid, and Green. |
Switches
Switches available in the library:
Single-phase charger
| Switch | Description |
|---|---|
| authentication | Allows to select if the charger will automatically start to charge or if it needs authentication. |
| lock | Allows to select if the charger is locked or not. When the charger is locked, no charging is possible. |
Three-phase charger
| Switch | Description |
|---|---|
| authentication | Allows to select if the charger will automatically start to charge or if it needs authentication. |
| lock | Allows to select if the charger is locked or not. When the charger is locked, no charging is possible. |
| force_single_phase | Allows to put the three-phase charger in single-phase mode or three-phase mode. |